iMaxRC X80AC Charger Introduction
X80 AC Balance Charger is the traditional balance charger with LCD display and buttons. AC/DC function, 80Watts, 6A charge current. The best choice for low budget.
iMaxRC X80AC Charger Connections
1.Connect the charger to its power source, using either the AC power cord or the DC power cord provided. When connected to power, the charger will make a single audible tone.
When connecting to a DC power source, make sure to observe connect polarity-red to positive and black to negative. Do not connect both power inputs to the charger at the same time!
2.Plug the output power adapter cord into the output power ports of the charger, making sure to observe correct polarity (red to red and black to black).
3.Plug your battery into the output power adapter cord. If you're charging a LiPo battery, plug its balance connector into the matching balance port on the charger, too.
Depending on the power connector on your battery, you may need to use an adapter or change the connector to match. In addition, if your LiPo battery does not feature an XH balance connector, an adapter board can be used.
Simple - efficient user interface
The user interface makes operation easy, with powerful function and abundant content. Real-time shows you the battery voltage, charger current, temperature of batteries, capacity of charge/discharger, elapsed time, input voltage etc., therefore, you can inquire the present state and establish various safety-limited parameters conveniently.
Individual battery charging/discharging and various charging mode
It accepts individual battery charging/discharging, so you can extend the scope of application of the charger. That is equally useful for the DIY battery. Various of charging mode to meet different demand: charging-auto/balance charging/fast charging/storage and cyclic charging etc.
iMaxRC X80AC Charger Features
iMaxRC X80 AC balance charger employs an advanced charging calculation and design which allow multilayer error to be compatible. It can create a safe charging condition and maximum reduce the danger caused by negligence or setting error of user. It adopts prevalent Synchronous buck - boost converter technology, this makes conversion efficiency up to 90%. It accepts all types of R/C batteries: LiPo, Li-ion, LiFe, NiMH, NiCd, Pb. During the process, it can monitor and balance each cell of the pack individually (Tolerance: +- 0.01V). This charger employs an individual-cell-voltage balancer to maintain you pack in balance while charging/discharging.
Five data of batteries and 1-5 cycles
For users convenience it can store and load maximum five data of different batteries. You can establish the data contains program setting of the battery to charge or discharge continually. Three data can be called out at any time you need and the process can be executed without program setting. Perform 1-5 cycles of charge>discharge or discharge>charge continually for NiMH/NiCd refreshing.
iMaxRC X80 Warnings
1.Observe any cautions and warnings included with your battery.
2.Never leave the charger unsupervised during use. If any malfunction is observed, immediately terminate the process.
3.Keep the charger away from moisture, dust, dirt, heat, direct sunlight and vibration. Do not drop it.
4.The charger is designed to be powered by an 11 to 18V DC or 100 to 240V AC power source only. Do not connect both power inputs to the charger at the same time!
5.Double-check all connections prior to starting the charge process. Do not connect with reverse polarity.
6.The charger and the battery to be charged should be placed on a heat-resistant, non-flammable and non-conductive surface. Never place them on a car seat, carpet or similar. Keep flammable and volatile materials well away from the operating area.
7.When charging LiPo batteries, we suggest using a LiPo charging safety bag, available from most hobby retailers.
8.Never charge a LiPo battery that is swollen in any way.
9.To avoid short-circuits between the output power adapter cord input connectors, always connect the adapter cord to the charger first and only then to the battery to be charged. Reverse the sequence when disconnecting.
iMaxRC X80AC Charger Specifications
- Operating voltage range: AC 100-240V, DC 11-18V
- Charge power: Max 80Watts
- Discharge power: Max 10Watts
- Charge current range: 0.1-6.0A
- Discharge current range: 0.1-2.0A
- Lilo/Lipo/Life battery count:1-6 Series
- NiCd/NiMH battery count: 1-16 Cells
- Pb battery voltage: 2 to 24V
- USB charge: 5V/2.1A
- Dimension: 148*140*48mm
- Weight: 0.55kg
- Syetem: iM.OS V2.15
- Operating Temperature: 0-50C
iMaxRC X80AC Charger Includes
- iMaxRC X80 AC Balance Charger x1
- AC Input Cord x1, DC Input Cord x1
- Output Cord x1
- Instruction manual x1
Trova video
Discuti sul forum
Cerca nel blog
